Need 1 Swing diff bearing!

Lo cash lester · Post by **Lo cash lester** » Sat May 29, 2004 8:56 pm

I need one good swing axle diff bearing. Had a bad one on a trans and need to replace. Drop me an eamil if you got one lester@locashracing.org.

Kubelmann · Post by **Kubelmann** » Sun May 30, 2004 12:08 pm

Call Weddle Industries at 805 696-9667

They have the parts and ship stuff right out. Great people, good prices, most highly reccomended. K-mann

Lo cash lester · Post by **Lo cash lester** » Sun May 30, 2004 5:30 pm

I deal with them all the time. I was hoping someone would have one sitting around.

Kubelmann · Post by **Kubelmann** » Sun May 30, 2004 6:05 pm

I know what you mean. Your partner John was really helpful when I was working on building my ebrake cables for my Off road Thing. You guys are very cool. IF I had the bearing it would be in the mail to you postage free. Come on folks, step up and send Lester the bearing. I have a pair of good used Thing diff outer bearings that are sitting. But I am pretty sure they are too small for your need. K-mann

Post by **Henryhoehandle** » Sun May 30, 2004 7:19 pm

Kubelmann wrote:I know what you mean. Your partner John was really helpful when I was working on building my ebrake cables for my Off road Thing. You guys are very cool. IF I had the bearing it would be in the mail to you postage free. Come on folks, step up and send Lester the bearing. I have a pair of good used Thing diff outer bearings that are sitting. But I am pretty sure they are too small for your need. K-mann

Ok,
I should have a good used one lying around.. LO cash Lester, email me your addy..

Kubelmann · Post by **Kubelmann** » Sun May 30, 2004 11:08 pm

Why am I not surprised to see Eric to jump up to help out a fellow VW bro in need. K-mann

Lo cash lester · Post by **Lo cash lester** » Mon May 31, 2004 8:21 am

Thanks!!!

I'll drop you an email with my address. I love VW people, always lookig to help out!

Post by **Henryhoehandle** » Tue Jun 01, 2004 6:18 pm

Your bearing is ready!
I will send it out tomorrow (6-2-04) via snail mail.
No problem at all to help someone out.. because I can remember when I was there and I have have had a lot of people help me out, and I may need it again in the future...

Eric

Lo cash lester · Post by **Lo cash lester** » Tue Jun 08, 2004 6:02 pm

Eric,
Just got back into town today and bearing was waiting on me.

THANKS!!! If there is ever anything I can help you out with just let me know. Lester

Post by **Henryhoehandle** » Tue Jun 08, 2004 7:02 pm

Lo cash lester wrote:Eric,
Just got back into town today and bearing was waiting on me. THANKS!!! If there is ever anything I can help you out with just let me know. Lester

Glad to help.

Now that you mention it, there is something that I need. I need one Chromoly (Scat, CB, etc) medium length (top outer stud-not the deep sunk # 3 cyl. one) 8mm head stud. I will be using about a 1/2 inch spacer under the cylinders so I need a long stud. Stock length is too short. I hate to spend 50 bucks for a complete set since I only need one. The ones I have are Scat but any good Chromoly one will be fine..

Eric

Lo cash lester · Post by **Lo cash lester** » Wed Jun 09, 2004 2:34 pm

Let me take a look at what I have. I'll be in the garage this weekend cleaning so we'll see. If I have one it's on the way to you. Lester

Post by **Henryhoehandle** » Wed Jun 09, 2004 4:31 pm

Thanks!!

Eric

Lo cash lester as guest · Tue Jun 15, 2004 12:08 pm

I looked and all I have is 3 sets of stock

. I have a block with a set of chromolly but would rather not pull it apart. Sorry, but if I run across some I'll give you a hollar.