My -54 Ratlook & -55 oval

bugsterkafer · Post by **bugsterkafer** » Sat Dec 16, 2006 11:44 am

Wow great work

SuperTrigger · Post by **SuperTrigger** » Wed Jan 24, 2007 11:13 am

heh thanks man...

Here is some more... This one was quite difficult point to do

some more welding in rear section...

This side came out quite well other didn't...

Front firewall going back. I took it from one rusty -56 oval, luckily this was one piece that was almost rust free sections in that body, almost everything else was gone by the winds...

SuperTrigger · Post by **SuperTrigger** » Sat Jan 27, 2007 9:18 am

Todays work...

Small hole in my trunk...

This one needed some hammering...

Good enough for me

SuperTrigger · Post by **SuperTrigger** » Sat Mar 03, 2007 10:55 am

Back to work again... I have been busy doing this as much as I can but seems that planning and fabricating new medal parts takes so much time and effort...

Here is pics from tankframe creation...

Some more in my gallery...

-ST-

SuperTrigger · Post by **SuperTrigger** » Thu Mar 08, 2007 9:51 am

Progress in rearend... Of course I hade do re do both sides because I didn't pay attention that top of that triangle isn't straight, it's gently curved...

I think I have to test fit fenders and all other things more often than I do now...

I had to redo co-driver side front fenders fittings, no it is solid. Not ready in picture below...

More to come...

-ST-

SuperTrigger · Post by **SuperTrigger** » Sun Mar 11, 2007 12:07 pm

Test fitting doors. one is tight other loose...

this one is tight... is that cap enough?

this one is pit loose...

same side with different door.. better...

What is usually cap between door to pillar or to side?
Some more pictures in my gallery

-ST-

SuperTrigger · Post by **SuperTrigger** » Thu Mar 15, 2007 7:01 am

Made new rearapron. I think it's quite good...

SuperTrigger · Post by **SuperTrigger** » Wed Mar 21, 2007 6:42 am

Progress from last Friday, yeaterday and today... test fitting all together... it's starting to look like a car...

SuperTrigger · Post by **SuperTrigger** » Sat Jun 21, 2008 3:48 am

Hi agan fellas!

Seems that my project is goin forward again. I hade small 1½ year pause because I build new home to my family and garage for me.

Anyhow here is small peaks from my progress. Let's hope I can make to strip as soon as possible

Chassis painted

testfitting parts nad planning for seat prakets

And the engine...

Some more in my gallery

-MP-

SuperTrigger · Post by **SuperTrigger** » Sat Mar 14, 2009 12:12 pm

Hohoo I have finally got some effort with my oval... Got it on floor pan again...

here is more of it

-MP-

SuperTrigger · Post by **SuperTrigger** » Mon Apr 20, 2009 1:15 pm

some progress...

some mumbling in here

SuperTrigger · Post by **SuperTrigger** » Wed Apr 29, 2009 3:54 am

few uppdates

more at http://rotta.markopuikkonen.com

SuperTrigger · Post by **SuperTrigger** » Thu May 07, 2009 11:45 pm

Some effort again... More at Rotta.markopuikkonen.com

SuperTrigger · Post by **SuperTrigger** » Sun May 24, 2009 1:30 am

Made to dyno but just before power pull something happened...

More in my blog

-MP-

grimace007 · Post by **grimace007** » Mon May 25, 2009 6:21 am

you are doing a wonderful job and should be very proudof what you are creating!